An installed church LED wall typically starts around $225 to $350 per square foot for a P2.9 to P3.9 sanctuary wall, $300 to $450 at P2.5, and $450 to $650 at P1.95. A 14 x 8 ft center wall lands roughly $25,000 to $73,000 depending on pitch. A site walk sets the real number.
This guide is written for the tech director, the facilities committee, or the pastor who has been asked to bring a number to the next meeting. The ranges come straight from the same price bands our LED Wall Calculator uses, so you can check any figure here against your own room in about a minute.
What "installed" includes
Every range on this page is a starting number for a full-scope installed wall: the LED panels, the processor that drives them, the mounting, and commissioning by our crew. Four things are quoted per project on top of that:
- Structure: any wall reinforcement or steel stays with a licensed contractor.
- Freight: shipping the wall to your building.
- Spares: extra modules and a power supply kept in the building for fast fixes.
- Content: motion backgrounds, lyric templates, and anything custom.
Church LED wall cost by size
A sanctuary wall is priced by the square foot, and the rate depends on pixel pitch. These are the most common center-wall sizes we see requested, priced at the three pitch tiers sanctuaries use. Each figure is the wall area multiplied by the calculator band, rounded to the nearest $500.
| Wall size | Area | P1.95 (front row within 13 ft) | P2.5 (front row 13 to 18 ft) | P2.9 to P3.9 (front row 18 to 28 ft) |
|---|---|---|---|---|
| 10 x 6 ft | 60 sq ft | $27,000 to $39,000 | $18,000 to $27,000 | $13,500 to $21,000 |
| 14 x 8 ft | 112 sq ft | $50,500 to $73,000 | $33,500 to $50,500 | $25,000 to $39,000 |
| 15 x 11 ft | 165 sq ft | $74,500 to $107,500 | $49,500 to $74,500 | $37,000 to $58,000 |
| 20 x 11 ft | 220 sq ft | $99,000 to $143,000 | $66,000 to $99,000 | $49,500 to $77,000 |
Starting points, not a quote. The low end of each band is where a straightforward single wall starts. A second surface, a curve, or a more capable processor moves the number up the band. The real figure comes after a site walk. For the full price-per-square-foot table across every pitch, see what an LED video wall costs.
What drives the cost of a church LED wall
Pixel pitch and front-row distance
Pitch is the biggest lever. It is the distance between pixels, and the right pitch is set by how close your nearest regular seat is to the wall. Finer pitch packs in more LEDs and costs more per square foot, so the goal is the coarsest pitch that still looks clean from the front row. Most sanctuaries land between P1.9 and P2.9. A scenic wall behind the band, viewed from farther back, can run coarser. Our pixel pitch guide explains the trade in plain terms.
Indoor brightness
A sanctuary wall needs to read under full stage wash and window light, which is where projection fails. Indoor walls run 1,000 nits or more, tuned to the room so the wall serves the service instead of overpowering it. A room with large windows may push the spec up; a darker room does not need to pay for brightness it will never use.
Processor and inputs
The processor takes the feed from ProPresenter, a laptop, or your switcher and maps it onto the wall. One wall with one input sits at the bottom of the band. Multiple inputs, IMAG plus lyrics, or redundant processing for a broadcast service move it up.
Structure and mounting
The wall hangs on rails or a frame on the existing wall, stands on a ground stack, or hangs from above. Mounting hardware is in the installed price. If the wall behind the stage needs reinforcement, that structural work stays with a licensed contractor and is scoped after the site visit.
Install and commissioning
Our crew installs the cabinets, levels and locks them, runs power and data, connects the processor, and tests every pixel before anyone sees content. Your team learns the system at handoff, and our support line stays open after.
Power
An LED wall draws far less on a typical service than at full white, but the circuits have to be sized for the maximum. The calculator shows average and maximum power for your wall size, and your electrician confirms whether the existing circuits cover it or a new one is needed.
One center wall or side screens?
The common layouts are a single center wall behind the stage, two side screens for lyrics, or both. For a fixed budget, one center wall usually buys more picture, because every additional surface adds its own processing, cabling, mounting, and commissioning time. Side screens make sense when the room is wide and the back corners cannot see a center wall clearly. We will price both paths so the committee can compare them side by side.
Is an LED wall cheaper than a projector?
Up front, no. A projector and screen cost less on day one. Over the life of the wall the gap narrows: an LED wall has no bulbs, lamps, or filters to replace, no alignment to redo, and the best LED is rated for 100,000+ hours. It also works with the lights up, which a projector does not. Our LED wall vs projector guide walks through the full comparison, and our page on replacing a church projector with an LED wall covers what changes for the volunteer team.
Skip the math. Our LED Wall Calculator turns your dimensions and viewing distance into a recommended pitch, panel count, resolution, power, and a starting investment estimate, in about 60 seconds.
Timeline: from budget range to a wall on Sunday
- Calculator: enter the wall size and the front-row distance to get a pitch and a starting range.
- Site visit: we measure the room, check mounting and power, and confirm the pitch.
- Written quote: a full spec and price the committee can review, with the two-year U.S.-based warranty in writing.
- Build and ship: built-to-order walls run roughly seven to eight weeks door to door, with the date confirmed in writing at order.
- Install and training: our crew installs and commissions the wall and trains your volunteers at handoff.
Common questions
How much does an LED wall for a church cost?
Installed, a church LED wall typically starts around $225 to $350 per square foot at P2.9 to P3.9, $300 to $450 at P2.5, and $450 to $650 at P1.95. A 10 x 6 ft wall starts around $13,500; a 20 x 11 ft wall at P1.95 can reach $143,000. The site walk sets the final number.
Can we start before anyone visits the church?
Yes. The calculator gives a size, pitch, panel count, power, and a starting range in about a minute. That is enough for a first budget conversation. A site visit confirms it before anything is ordered.
What pitch does a sanctuary need?
Measure to your closest regular seat. Within about 13 ft, P1.95. From 13 to 18 ft, P2.5. Beyond that, P2.9 to P3.9 is usually plenty. The calculator applies the same rule.
What is not included in the installed price?
Structural work by a licensed contractor, freight, spares, and content are quoted per project. Panels, processing, mounting, and commissioning are in the range.
What warranty comes with the wall?
A two-year U.S.-based warranty covers defects. Modules swap from the front, spares stay in the building, and our support line answers the phone.
How do we get a real number for the board?
Send us your room: wall size, distance to the front row, and a few photos. A production pro comes back with a spec and a price, and we set up the site visit from there. If you are still comparing options, our houses of worship page covers the spec side.